187
This document, and the content contained herein, is intended for customers, users and other persons with the operation and features of the covered Hegla products. While Hegla makes every effort to include accurate and useful information, it is not possible to anticipate or address every possible situation or to account for conditions at unknown locations or interactions with unknown systems or components. Therefor, these documents must be used only for informational purposes and used in conjunction with best practices and with due care. Hegla shall not be responsible for any injuries or losses that occur as a result of the information in this document. Moreover, as products and offerings change over time, the usefulness of the information in this document may become obsolete. It is the responsibility of the reader or consumer to ensure that the information contained herein is timely and reflects the current reality of Hegla products and offerings. Hegla disclaims any and all warranties regarding the information in this document.
***Read chapter 1 of your operators manual before undertaking any work in the area of the overhead crane equipment.***
When in doubt please contact Hegla service before taking action (404) 763-9700
How to reference a friction gantry (Bridge/Trolley/Tilting/Lifting/Turning)
Section 1
To reference the friction gantry axis' you must do the following:
- First, you need to release the gantry to get it to its minimum limit switch. See Highspeed Gantry - How to release the gantry.
- Now drive the gantry onto its minimum limit switch (pertains to bridge & trolley only).
- Once on the limit switch, return to the panelview home screen and click the service softkey as shown below.
- Now click the login soft key as shown below.
- Once you click service a pop up window will appear. Try the following usernames and passwords:
| Username: | Hegla |
| Password: | D37688 |
| Username: | 1 |
| Password: | 0100 |
- Once you are logged in your screen should look like the one shown below. Then click the system soft key.
- Once you have clicked the system softkey you should see the screen below. Now click the Set Zero P. soft key.
- After clicking the Set Zero P. softkey you should get to a screen that allows you to choose from the following:
- Master (section 2)
- Trolley (section 3)
- Tilting (section 4)
- Lifting (section 5)
- Turning (section 6)
Section 2
Setting the zero point of the bridge drive:
- To set the zero point (reference) of the bridge, click the bridge set zero soft key in the "Set Zero Point" menu as shown below.
- In order to start the reference, the gantry must be in manual mode on the operator console selector switch, in "operation mode window" tab down to reference and press the enter key (you must press the enter key and highlight reference).
- Once the bridge is on its limit switch and the operators desk toggle switch is on manual mode, press the start reference soft key.
- The bridge encoder count should change to 100 and the status window should display "reference okay". If this is correct, then the bridge drive has completed reference.
- Change the bridge drive back to "AUTOMATIC" in the operating mode window.
(IMPORTANT OR GANTRY WILL NOT MOVE WHEN COMMANDED).
Section 3
Setting the zero point of the trolley drive:
- To set the zero point (reference) of the trolley, click the trolley soft key in the "Set Zero Point" menu as shown below.
- In order to start the reference, the gantry must be in manual mode on the operator console selector switch, in operation mode window tab down to reference and press the enter key (you must press the enter key and highlight reference).
- Once the trolley is on its minimum limit switch and the operators desk toggle switch is on manual mode, press the start reference soft key.
- The trolley encoder count should change to 100 and the status window should display "reference okay". If this is correct, then the bridge drive has completed reference.
- Change trolley drive back to "AUTOMATIC" in the operating mode window. (IMPORTANT OR GANTRY WILL NOT MOVE WHEN COMMANDED).
Section 4
Setting the zero point of the tilting drive:
- In order to start the reference, the gantry must be in automatic mode on the operator console selector switch. Then from the "Set Zero Point" menu press the tilting softkey.
- In order to start the reference, the gantry must be in automatic mode on the operator console selector switch, in operation mode window tab down to reference and press the enter key (you must press the enter key and highlight reference).
- Press the start reference soft key.
- The tilting frame should drive on and back off of the minimum limit switch on its own and the encoder count of the tilting should be in a window of 100-150. The status window should display "reference okay". If this is correct, then the tilting drive has completed reference.
- Change tilting drive back to "AUTOMATIC" in the operating mode window. (IMPORTANT OR GANTRY WILL NOT MOVE WHEN COMMANDED).
Section 5
Setting the zero point of the lifting drive:
- In order to start the reference, the gantry must be in automatic mode on the operator console selector switch. Then from the "Set Zero Point" menu press the trolley softkey.
- In order to start the reference, the gantry must be in automatic mode on the operator console selector switch, in operation mode window tab down to reference and press the enter key (you must press the enter key and highlight reference).
- Press the start reference soft key.
- The lifting frame should drive on and back off of the minimum limit switch on its own and the encoder count of the tilting should be in a window of 100-150. The status window should display "reference okay". If this is correct, then the lifting drive has completed reference.
- Change lifting drive back to "AUTOMATIC" in the operating mode window. (IMPORTANT OR GANTRY WILL NOT MOVE WHEN COMMANDED).
Section 6
Setting the zero point of the turning drive:
- In order to start the reference, Turn to the home position slowly in manual mode (cups pointing towards the tilting table).
- When the suction frame is mechanically straight to the tilting table come back to the panelview and from the "Set Zero Point" screen select the turning softkey.
- Once you have selected the turning softkey you will see the screen below. Press and hold the set zero softkey for 3 seconds and the active position window should show an encoder count of 1000. If it does not, try just simply clicking the set zero softkey.
- If the encoder shows a count of 1000 after the reference then the reference for the turning drive is complete.
